Plumber Eveleigh

We provide commercial and domestic plumbing across Eveleigh, covering blocked drains, burst pipes, hot water, gas fitting, and leak detection. All attending technicians are properly licensed NSW plumbers (Licence 305428C), and we're fully insured with current Public Liability and Workers Compensation policies. This protects you if accidental property damage happens during the job or in relation to workplace injuries.

Our team arrives in uniform, confirms identity at the door, and explains the scope in plain English before starting. We use drop sheets or protective covers in work areas and wear boot covers or clean shoe covers when requested or when conditions require it. At the end of the job, we clean up debris generated by the work and remove it from site. If diagnostics indicate a more involved repair, we explain the options and confirm scope before any additional work proceeds.

The fixed-price model means you receive an upfront quote based on confirmed scope, and the price is by the job, not by the hour. There are no hidden costs. The quote is valid for one month from the date issued, and you can decide whether to proceed once the price is confirmed. For customers mentioning "web55," we offer $55 off (limited to one per person on paying jobs).

We service the entire Eveleigh area and can travel up to a 60km radius from our base hubs for emergency calls. Arrival timing depends on current bookings and traffic conditions, but urgent jobs are prioritised and the nearest available technician is dispatched. Where possible, we provide ETA updates when you book.

A dripping tap typically results from a worn washer, faulty valve seat, or corroded O-ring. Left unaddressed, a slow drip can waste hundreds of litres per month and increase your water bill. We locate the source of the leak using visual inspection and pressure testing, then repair or replace the necessary components to restore a watertight seal.

For older tap assemblies, parts may no longer be available, in which case we recommend replacement with a modern mixer or separate hot/cold tap. We confirm the existing plumbing configuration (whether the taps are connected to mains pressure or a gravity-fed system) and ensure the new fixture is compatible before quoting. All replacement taps are installed to Australian Standards and tested for leaks before departing.

We also handle concealed leaks behind walls or under sinks. If moisture is present but the source isn't obvious, we use electronic leak detection equipment to pinpoint the fault without invasive demolition. Once the leak is located, we explain the repair options and provide a fixed-price quote before proceeding.

Addressing leaking taps promptly reduces water waste and prevents secondary damage such as mould growth or timber rot in cabinetry. If you notice a drip or moisture around a tap, arrange an assessment so the fault can be confirmed and repaired.

Shower faults in Eveleigh properties range from dripping showerheads and low water pressure to concealed leaks behind tiles. A dripping showerhead usually indicates a worn washer or faulty cartridge inside the mixer valve. Low pressure can result from sediment buildup in the showerhead, a partially closed isolation valve, or pressure issues elsewhere in the property (common in taller apartment blocks where pressure varies by floor).

We start by testing water pressure at the showerhead and isolating the cause. If the issue is localised to the shower, we disassemble the mixer, inspect internal components, and replace worn parts. If pressure is low throughout the property, we check the mains supply and any pressure-reducing valves. For concealed leaks (where moisture appears on walls or ceilings below the shower), we use moisture meters and thermal imaging to locate the fault without unnecessary demolition.

Once the fault is identified, we explain the repair options and provide a fixed-price quote. Repairs are completed to Australian Standards, and we test flow and temperature before leaving. If tiles need to be removed to access pipework, we take care to minimise damage and can coordinate with tilers for reinstatement if required (tiling itself is outside our scope, but we work with trusted trades when needed).

If your shower is leaking, has inconsistent temperature, or low pressure, book an assessment so the cause can be confirmed and repaired.

All gas work in NSW must be performed by a duly licensed gas fitter and comply with AS/NZS 5601.1 safety standards. We install, repair, and maintain gas appliances including cooktops, ovens, hot water systems, and heating units across Eveleigh. Common issues include gas leaks (indicated by the distinctive "rotten egg" odour, hissing sounds near appliances, or dying vegetation over underground lines), faulty pilot lights, or appliances that won't ignite.

If you smell gas, turn off the gas supply at the meter if safe to do so, open windows to ventilate the area, and do not operate electrical switches or create sparks. Call us on 1800 349 338 and we'll arrange immediate dispatch so the system can be assessed and made safe.

For new gas appliance installations, we confirm the existing gas supply capacity, run new lines if required, connect the appliance, and perform a pressure loss test to ensure the system is gas-tight. A compliance certificate is issued upon completion to verify the installation meets safety standards. For gas leak detection, we use combustible gas detectors and thermal imaging to locate the fault, then repair or replace the affected section and retest the system.

All gas fitting work is completed by licensed gas fitters (Licence 305428C) and backed by our Lifetime Labour Warranty on workmanship. Manufacturer warranties apply to gas appliances and hardware.